Atdec Telehook TH-3070-CTW Installation manual Bedienungsanleitung PDF herunterladen

G Attaching the Mount to the Ceiling Hanger

M8x10mm

Screw

Swivel Insert

Step 1

Attach the three Swivel Inserts to the hanger in the height that

you have chosen for the mounting of the display.

Step 2

Attach the front and rear Hanger Pole Collar so that it sits on

the swivel collars as shown above. Tighten the M8x30mm

screws so that the hanger pole collars is secure, however do

not over tighten.

Note: This operation will require two persons.

Lift the display with brackets attached and hook the brackets over the

sliders. Hold the display firmly and insert the two M8x45mm screws

and tighten by using the Long 6mm Allen Key.

Note: The brackets

should rest on the

horizontal bar with the

slider between the

bracket.

I Mounting the Display

Swivel Insert

Collar Front

Collar Rear

H Attaching the Mount to the Ceiling Hanger

Ceiling

Mount

Cables

Step 1

To use the in-built cable management, remove the Ceiling

Mount Cover and feed the cables through the cable hole.

Step 2

Cut out enough space in the Ceiling Mount Cover to allow

the cables to exit from, then push the Ceiling Mount Cover

up, until in sits flush with ceiling.

Ceiling Mount

Cover

Ceiling Mount

Cover

Cables

Ceiling

Mount

Cut Out

M8x30mm

Screws

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 15/08/12 ©

J Adjusting the Viewing Position of your Display

Step 1

Loosen the two M8x45mm screws, and adjust the

tilt angle of the display to the required position.

Tighten the two locking screws with the Long

6mm Allen Key provided.

WARNING: Do not attempt to adjust tilt

angle without firstly loosening locking

screws.

Doing so may damage the product.

6mm Allen Key

Adjust grub screw 1 until the display sits level. Once the

display is level, tighten grub screw 2 until it firmly tightens onto

the horizontal bar. Tighten grub screw 3 firmly until it firmly

tightens onto the horizontal bar and prevents it from moving.

360° Rotation

Tighten

-5° to 5°

K Attaching the Adhesive Vinyl

Adhesive

Vinyl

M8 Small

Washer

M8x45mm

Screw

Long 6mm

Allen Key

Tighten

Loosen

-5° to 25°

Tilt

Hanger

Horizontal Bar

1. Tilt Adjust

Component Checklist

M10 Steel

Washer (x4)

Nylon Plug

(x4)

M8 x55mm

Screw

M10 Coach

Screw (x4)

A Mounting the Ceiling Mount

NOTE:

The manufacturer

does not accept

responsibility for

incorrect installation.

The installer should

satisfy himself that the

ceiling is strong

enough to support the

Telehook Flat Panel

Ceiling Mount unit of

14kgs (31lbs) plus the

maximum allowable

monitor weight of

91kgs (200lbs).

Total of 105kgs

(231lbs).

Telehook Flat Panel

Ceiling Mount

supports a maximum

weight of 91kgs

(200lbs)

TOOLS REQUIRED:

Power Drill

12mm (1/2”) Drill Bit

7mm (9/32”) Drill Bit

Adjustable wrench

Ceiling Mount

IMPORTANT:

Ensure you have received all parts against the component checklist prior to installing.

Bits Box

12mm (1/2”)

Hole

Nylon Plug

M10 Coach

Screw

Masonry

Ceiling

Masonry Mounting Option

Timber Beam Mounting Option

Timber

Beam

M10 Coach

Screw

7mm (9/32”)

Hole

Inner Hanger

M8 x10mm

Screw (x24)

M6 x12mm

Grub Screw

(x3)

M10 Washer

Collar Front

Collar Rear

Swivel Insert

(x3)

Adhesive Vinyl

Strip (x6)

M8x30mm

Screw (x4)

NOTE: Ensure all four M10 Coach Screws are used when mounting the Ceiling Mount.

Note: The Vinyl Strips may need to be cut to length

depending on the hanger configuration chosen.

The Telehook Flat Panel Ceiling Mount’s

set up is now complete. The remaining

unused holes can be covered using the

6 white adhesive vinyl strips for improved

aesthetics. Peel the backing from the

strip and apply the adhesive side onto

the hanger(s) so that they cover the

unused holes.

Padlock

(not supplied)

5mm (

”)

diameter shackle

For added security you may

choose to attach a padlock to

one or both brackets to prevent

the theft of the display. It is

recommended that the padlock

should have a shackle diameter

of 5mm (

”).

L Security Option

2. Pan Adjust

3. Horizontal Adjust

Wall Mount Horizontal Bar

Slider (x2)

Hanger Joiner

Extension Hanger

Collar Joiner

Installation Instructions

Flat Panel Ceiling Mount

M8 x45mm

Locking Screws

(x2)

Multi

Washer (x6)

M5 x16mm

Mounting

Screws (x6)

M6 x16mm

Mounting

Screws (x6)

M8 x16mm

Mounting

Screws (x6)

M4 x16mm

Mounting

Screws (x6)

Long 6mm

Allen Key

M8 Small

Washer

(x2)

3mm

Allen Key

5mm

Allen Key

M8 Small

Washer

M8x45mm

Screw

Long 6mm

Allen Key

Tighten

6mm Allen

Key

TH-3070-CTW

Ceiling Mount Cover

Wall Mount Bracket (Left)

Wall Mount Bracket (Right)

Clinch Nuts

To lock the position firmly tighten all 4 M8x30mm screws.

If free rotation of the display is required, only lightly tighten the

4 M8 x 30mm so that movement of the display is possible.

1 2

Inhaltsverzeichnis

Seite 1 - TH-3070-CTW

G Attaching the Mount to the Ceiling HangerM8x10mmScrewSwivel InsertStep 1Attach the three Swivel Inserts to the hanger in the height thatyou have ch

Seite 2 - F Position Sliders

B Attaching the Ceiling Mount CoverSlide cover plate up. Ceiling MountCoverIf the ceiling mount is attached where a false ceiling is used,the ceiling

Kommentare zu diesen Handbüchern

Keine Kommentare

Atdec Telehook TH-3070-CTW Installation manual Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach TV-Zubehör Atdec Telehook TH-3070-CTW Installation manual herunter. Atdec Telehook TH-3070-CTW Installation manual User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für TV-Zubehör Atdec Telehook TH-3070-CTW Installation manual